|PECHORIN'S home account archive eshop globalmediapro|
My On Timer will not stop blinking and the television will not stay on over 10 seconds. The On Timer blinker (red) blinks until I unplug the power and then plug it in again or until I turn the power off and on again. The T.V. will come on after I do this but only for a few seconds and then the On Timer starts to blink again. The T.V. does not stay on long enough to change the On Timer or do anything to try to correct this problem. How can this problem be resolved?
16 comments, pages: 1 2 »Pages: 1 2 »
The following steps should be able to correct the problem: 1) Unplug the TV or remove AC power from the TV 2) Count to ten and then plug in the TV 3) Locate the [Menu], [VOL-] and [Power] button on the TV’s side panel 4) Using the buttons on the TV’s Side Panel, press and hold both the [Menu] and [VOL-] buttons. 5) While holding those buttons, press and release the [Power] button one time and count to 3 before releasing the [Menu] and [VOL-] buttons. 6) The TV’s lower left Blue Power LED will come ON. 7) Wait 30 seconds. Confirm that the blue LED on the Lower Left of the TV (not the iPod dock for iPod models) has remained ON during this time. 8) Press the [Mute] button on the TV remote twice 9) Unplug the TV or remove AC power 10) Count to ten and plug the TV in 11) The TV power should automatically come ON and the blue power LED with be ON 12) Wait 40 seconds and the TV picture should appear 13) You can now continue using your TV. 14) If the picture does not appear, power on the TV manually: · If the LED begins flashing, unplug and power ON a second time. · If the LED begins flashing again, power ON the TV without unplugging If the LED begins flashing again, contact us directly by phone to obtain a local authorized service center for you. If the TV does power on, please reply back with the software version number for us to research this issue. Please follow these steps to obtain the software version number: 1) Press the [Menu] button on the remote control. 2) Using the arrow keys in the center of the remote, scroll over to the "settings" menu and select the [OK] button on the remote 3) Scroll down to "system info" and select [OK] button on the remote
my tv jvc ,the on timer is blinking and never stop blinking on and on,and before ten seconds it went off, leaving no time to tune,but continue to blink. help please
My On Timer will not stop blinking and the television will not stay on over 10 seconds. The On Timer blinker (red) blinks until I unplug the power and then plug it in again or until I turn the power off and on again. The T.V. will come on after I do this but only for a few seconds and then the On Timer starts to blink again. The T.V. does not stay on long enough to change the On Timer or do anything to try to correct this problem. How can this problem be resolved? Reply
was there a fix for timer light blinking and tv wont turn on?
JVC TV AV-F2983 can't turn on, blinking light On-timer and ECO sensor.
I have this same exact problem with my television. It started two days ago for no know reason and we can't figure out how to remedy it. Please help, this is our only TV and we hope that there is an easy fix. thank you for your time and providing this resource Eric
i wacked my set and it started working again. who knew?
Hi Jorge I have the same problem for my JVC TV too. The Timer LED keeps blinking. May I know if you have solve it ? I called the local rep and they will charge me SG$80 to repair it. Thks a lot Vtec
I have the exact same problem with my TV.I found a web site where someone else was experiencing the same problem and suggested disconnecting the power for approx. 4 hours to clear the internal memory chip. Plugging back in after 4 hours should cause the TV to start with preset factory conditions. I tried it but it still does not work. Could it be my VCR that it is connected to that is causing the problem?
Got the same problem. Any ideas on how to fix it?