JVC service or questions

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better.

Stacy Sample
JVC Service & Engineering
Houston, Texas

Reply

• Re: JVC service or questions Joe M - 17th Jun 2006 21:14
  hi, i have a gr-dvl725u. I do not have the serial number because it has been ripped off. My camera says it is in safe guard mode and to reattach the battery. It is error EO2. I follow the instructions and it keeps doing the same thing. i also think it is wierd that i am able to still use mempry mode just perfectly and take as many photos as i want. If u know anything i could do that would be great.
  
  
• JVC model av48p575
  Jay
  - 17th Jun 2006 23:29
  I have this 48 inch widescreen model AV-48P575 it is a prjection hd tv and when i turned it on this morning the power indicator light just flashed and there was no picture. i turned off the power bar and the tv now turns on but the picture is out of focus and it seems extra white as far as the picture goes. Any ideas?
  
  Jay
  
  
• Re: JVC service or questions Rod Bruce - 17th Jun 2006 23:32
  Hi there,
  
  I am totally frustrated!
  
  For a year now, I have been trying to get my GR-D32U mini DV to connect to my
  computer. 3 Differnt computers will not recognize it. I have tried internal
  firewire cards, and PCMCIA.
  
  Any suggestions?
  
  If this doesn't work soon I am going to bouyancy test it. and buy a non JVC
  camera to replace it.
  
  Thanks
  
  
• Re: JVC service or questions
  arvin harris
  - 18th Jun 2006 1:31
  what are some of the option's for condensation operation i have a jvc gr-d9ou and it's driving me crazy!!!
  
  
• Re: JVC service or questions Brian LaRose - 18th Jun 2006 5:47
  Hi, I have a question concerning my QVC digital camera, model # : GR-D93U. I seem to have misplaced the manual. I was wondering how I could play film I recorded onto the television. I haven't been able to figure it out. I have the audio and video ports on the front of the TV, but I can't get it to work. Any help would be appreciative. Thank you.
  
  
  • Re[2]: JVC service or questions Bill Pinks - 7th Jul 2008 1:10
    Brian...I see this question is from '06 but in case you still need an answer on the 'playing video camera tape on your tv' question.....there should be a way on your DVD/VCR player/recorder to SELECT INPUT or SOURCE or INPUT. As a rule, there is an 'L1' or 'L2'(Line Input usually on the side or front of the player/recorder) depending on your model/brand that you need too engage the particular input you use. This will hopefully put your camera contents on the tv. Hope this helps you!
    
    
• Re: JVC service or questions Sam - 18th Jun 2006 13:24
  Solved the no power problem for JVC GR-D70U
  
  There are several small SMD fuses on the main circuit board in the top side left hand corner just next to the molex header that connects to the battery, dc input board. Of these three black fuses with white numbers on them, I found only two still conducted and so the 'faulty' one I shorted across by cleaning and the use of conductive silver paint (RS Components). You should then find that the 11V supply can be measured here with a multimeter. Ideally the fuse should be replaced rather than shorted, but I am lazy.
  
  PS try and note where all the screws go as there are about four different lenths!
  
  Sam
  
  
  • Re[2]: JVC service or questions JB38 - 18th Jun 2006 18:31
    Sometimes that fuse pops if, or as, the CCD develops a problem,(as well as for other reasons of course!). The silver paint referred to would represent a fuse value "grossly" in excess of whats used, these ranging from .2amps (200ma) to 1.6 amps, so "if" you managed to get the camcorder working it can be considered extremely lucky as there was a high danger of blowing a main IC, something which would make the camcorder an uneconomical repair due to the sheer cost of replacing the complete PCB. (PS: The GR-D70U being on the list of models which can potentially develop that fault)
    
    
• Re: JVC service or questions kevin koge - 19th Jun 2006 0:35
  How do i get my JVC model number GR-D90U out of safe gaurd mode? It flashes a error code EO6, Is there any easy fix, or do i have to take it in to a shop for repair? Thanks for your time. Kevin
  
  
• Re: JVC service or questions silvia - 19th Jun 2006 2:41
  yes i have been having an on going problem with my new video camara I have only used it one in December, and I took it out this month and it givs my a condisation error and the tape take. I called JVC and they where not nice nor could help me. i have taken all there advice and still not working. This is horible becuse my sisters wedding is in July and I want to use my video camara.
  
  Please help JVC 700X model GR-d22u
  Silvia
  
  
• Re: JVC service or questions
  nicole
  - 19th Jun 2006 8:10
  i need a parts number for a remote control ... JVC VCR HR-dx22ea I was given the VCR without a remote and need to try and replace it or get assistance with programming a universal remote to operate all functions... currently the universal only works to power on and off and play/stop/record etc. I need\want to tune in the stations and use timer record.
  
  
• Re: JVC service or questions Marla - 19th Jun 2006 15:21
  My computer doesn't read the image files from my camcorder. I have installed and uninstalled the software plenty of times and it still says there's an error reading the software. Can you please help me!!!!!
  Thank you,
  Marla