JVC service or questions

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better.

Stacy Sample
JVC Service & Engineering
Houston, Texas

Reply

• Re: JVC service or questions Jim Legans - 30th Jul 2006 2:01
  I bought a BN-VF733 battery for my Everio G GZ-MG21u camcorder.I attached it to my camera, plugged in the power cable and waited for 24 hours. When I turn on the camera the screen shows a diagram of a battery and a camera with arrows pointing to each and an 'x' in the middle. Above that diagram are the words "communicating error". I pushed the 'reset' button and that didn't fix the problem. Is there a fix for this?
  
  Thank you, Jim
  
  
• Re: JVC service or questions
  Gabriel
  - 30th Jul 2006 18:02
  I have a JVC 27" Tv, Model: AV 27920
  Manufacture Date Nov 1998
  
  Last night, turned the TV off, went to bed.
  
  This morning, when I turn the tv on, it makes that high pitch turning on sound, but no image comes up, then a few seconds later, it "shuts off", and the red LED starts semi bright blinking. pushing the power button does nothing at this point.
  
  Also, for the last few months, the very top of the tv was being reflect back town along the top of the screen.. making the top of the image slightly distorted.. and i think it has been getting worse..
  
  please advise,
  
  (should i attempt that capacitor replacement as described by other customers?)
  
  thanks
  Gabriel
  
  
• Re: JVC service or questions Dennis Dardanell - 30th Jul 2006 18:16
  I have a JVC GR-AX800U. Everything works fine except the viewfinder indications. There are none. Is this a major or minor problem? Worth getting fixed or not? Thanks in advance for your help.
  
  
• Re: JVC service or questions
  ricardo rodriguez
  - 30th Jul 2006 18:37
  I have a jvc 3 disc cd stereo. when i turn it on it says protect
  and cannot use it. Model #CA-MXK3. SYSTEM NO.MX-K3. AC 120V
  60Hz 105W. UL FILE NUMBER E207719. serial no.146h6754.
  Please help. thanks.
  
  
  • Re[2]: JVC service or questions Dave Moore - 27th Jan 2007 18:00
    I have a JVC CA-MXK3 stereo and it says 'protect' when I turn it on, and it will not work. How do I fix this problem?
    
    
• Re: JVC service or questions Keith Joiner - 30th Jul 2006 22:10
  Hello,
  
  Just found your Pechorin's site while searching for JVC error codes. I have a KD-LX100 car stereo that will not eject the CD and was showing an error code 25. After turning the car off then back on it now shows error code 26. Any help would be greatly appreciated.
  
  Thanks,
  Keith
  
  
• Re: JVC service or questions
  ernest chillura
  - 31st Jul 2006 0:42
  my jvc av-27820 has audio on all channels excet channels 8,9 and tnt, channel10 comes on with loud roaring sound. Hope you can help.
  
  
• Re: JVC service or questions
  Matt
  - 31st Jul 2006 10:13
  Hello.
  I own a JVC AV-32850 and just last night it stopped accepting a signal from my remote control. I changed batteries in the remote and since it is a universal I checked to see that it was still sending a signal to my other appliances, which it was. This leads me to believe that it is a problem with the television and not the remote. I re-entered the code for my TV into the remote and was still unable to use it with the television. Any suggestions?
  
  Thank you so much.
  
  
  • Re[2]: JVC service or questions Jennie - 4th Apr 2007 12:45
    I just ran across your question about the remote and I am having the same problem did anyone give you a good answer because I am not seeing any responses. Could you let me know. Thank you. Jennie
    
    
• Re: JVC service or questions adam m - 1st Aug 2006 1:25
  hi my jvc grdx77us is saying "please wait condensation detected" for hours and hours and i can't use it what can i do
  
  
• Re: JVC service or questions GODSSLDIER39507 - 1st Aug 2006 5:40
  HELLO STACY I HAVE THE GR-SXM87U OR EITHER THE GR-SXM37U JVC SUPER VHS DIGITAL SINGAL PROCESSING CAMCORDER AND IAM GETTING ON THE SCREEN S-ET AND MY PICTURE IS SCRAMBLED IAM ALSO NOT ABLE TO FIND A CLEANER TO CLEAN MY CAMCORDER CAN YOU PLEASE HELP ME THANK YOU
  
  
• Re: JVC service or questions
  Maria
  - 1st Aug 2006 13:49
  I have a jvc gr-dx97us and am having a problem with the zoom feature. when i turn on the camera - it automatically starts to zoom in to the max setting. when i change the zoom to 12x max, it will zoom to 12x automatically. when i zoom out, it zooms right back in as soon as I take my finger off the button. This happens with both zoom buttons and using either the viewfinder or the lcd. any ideas? thanks!