JVC service or questions

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better.

Stacy Sample
JVC Service & Engineering
Houston, Texas

Reply

• Re: JVC service or questions Joseph Raghavan - 16th Oct 2006 4:53
  I have a JVC cam. Can't remember the model but jst like some else who wrote in , I have the same prob whereby it keeps saying lens cap on and shows a blank screen whereas the lens cap is off. I am in Kuala Lumpur, Malaysia. What's wrong with my cam and where is the nearest service centre ?
  Thanks,
  
  Joe
  
  
  • Re[2]: JVC service or questions
    Peter
    - 16th Oct 2006 17:25
    This is a nkow issue to JVC. It might be related to the defective CCD. You should contact JVC to see if they can fix it for free. You might have to pay the shipping. Good Luck, Peter
    
    
• Re: JVC service or questions
  pvenk
  - 16th Oct 2006 5:27
  I purchased a JVC GR-D72US camcorder a few months ago. Recently, the LCD display stopped showing the picture. I can still see the picture using the viewfinder; but not on the LCD monitor. What's wrong and how can I correct it?
  
  If I need to purchase a certain spare part, can you please let me know the part number as well as the best place to buy it in USA?
  
  --pvenk
  
  
• Re: JVC service or questions
  JOHN ROSE
  - 16th Oct 2006 20:09
  re jvc tv model AV-29SX2EK or chassis type.
  how can i enter set up mode to alter gun drive adjustment for grey scale
  
  
  • Re[2]: JVC service or questions
    JB38
    - 17th Oct 2006 12:42
    My info states that if you push "I" and "mute" on the handset at the same time that should take you into the service mode, other than that regrettably I dont have any further information.
    
    
• Re: JVC service or questions John Bruecker - 16th Oct 2006 20:57
  Have JVC GRD-DVL9000U Camcorder after 15 sec in record or playback mode screen turns blue and flashing E03 code appears on screen and unit will not work. When I power off and on it works again for about 15 seconds, have removed batt. and done reset, same happens, please advise, thanks
  
  
• Re: JVC service or questions Lee Van Horn - 16th Oct 2006 22:20
  I have a JVC AV35750. When turned on the sound is good but screen shows only a bright horizontal line about 3/4 inch tall across the screen. Adjusting gives no results. Can anyone help?
  
  
• Re: JVC service or questions
  John
  - 17th Oct 2006 0:24
  Please help I have a JVC DVL820U video camera and I can't connect it up to windows XP. It can't find a connections. I think it is a software problem and I have went to the JVC web page and down loaded some up dates, but no luck and sujestions ...thanks
  
  
• Re: JVC service or questions
  deb
  - 17th Oct 2006 20:42
  mini dv
  model gr-d31u
  when i try to capture it says unable to connect device
  
  
• Re: JVC service or questions
  Chad Oden
  - 17th Oct 2006 23:41
  I have a JVC KD-SH55 CD player in my car and The error code 06 keeps showing up and the motorized faceplate will not come out. Can you help me?
  
  
• Re: JVC service or questions
  Jeff Robichaud
  - 18th Oct 2006 0:09
  My Dseries TV seems to be turning yellow I have had for 1 1/2 yrs and have tried adjusting through menu as well as back screws on set...any suggestions?
  
  
• Re: JVC service or questions Marcel - 18th Oct 2006 0:45
  I have a GR-DV500U that just stopped working after ~18 months.
  No power from AC adapter or battery at all.
  I brought it to a local repair shop and they say the PCB board needs to be replaced for about $600. I didn't believe that.
  
  Any idea?
  
  I would figure that there might be a fuse or a chip that shorted or something like that...
  
  Would appreciate insight.
  
  Thanks,
  
  Marcel