JVC service or questions

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better.

Stacy Sample
JVC Service & Engineering
Houston, Texas

Reply

• Re: JVC service or questions Aimee Bowen - 9th Oct 2006 18:38
  I have a JVC 48WP30 that is having convergence issues. Left and right hand upper corners are out of balance, convergence cannot be aligned, with red and blue out of alignment on those corners as well. This TV is only 3 years old and I am seriously upset about having to pay $350+ to get it repaired. Thank you!
  
  
• Re: JVC service or questions
  lewis block
  - 9th Oct 2006 21:57
  I have a dr-m10 video recorder that I have recorded a vhs tape to a dvd-rw disc in video mode and finalized and it plays fine in the dr-m10 unit. But I have a home sound system with a xv-d701bk dvd player and these discs will not play in the dvd player unit. What do I have to do to get these recorded discs to play on my xv-701bk unit? Thanks lewis block
  
  
• Re: JVC service or questions
  fred tobinski
  - 10th Oct 2006 3:08
  Hi Stacy, was there any solution to this problem , post copied below.
  
  Re: JVC service or questions
  Stephens - 20th May 2005 3:45
  I have a JVC television, model AV-27S33. It is hooked directly to cable, no cable box. Suddenly, I am unable to tune ANY channel below 48, but any 48 or above come in crystal clear. There is no hint of a picture on the lower channels, even if I turn off the blanking. My VCR still receives all channels perfectly normally. This is not a matter of not having the channels programmed into memory, I've gone through the channel setup numerous times, it just won't pick up the lower stations.
  
  Any help would be greatly appreciated!
  
  Reply
  
  
  
  Re[2]: JVC service or questions Brandon - 25th Sep 2005 8:24
  I am having the exact same problem. Earlier today I was watching channel 25 and it was getting snowier and snowier. Finally the signal gave out. I started flipping channels and I could not get anything under channel 48. Also, I intermittently could not get channel 98 & 99. I tried do a channel scan over and over again. I switch to air, I switched to cable. I unplug the TV for a couple hours. I changed the cables. No change. But my other 2 tvs and my VCR on this tv all receive all channels. I can't even watch my vcr on channel 3 of the TV (although I can watch it through the A/V connection).
  
  Re[3]: JVC service or questions Fred Tobinski - 8th Sep 2006 5:48
  I to am having this problem with the channels. Is there any solution??? please help.
  
  
• Re: JVC service or questions Brandy Shaw - 10th Oct 2006 21:58
  I recieved a JVC Gr-SMX260U for Christmas. Only two weeks later it fell from a table and the hit the port labeled DC IN, where the batter charger goes. The camera worked until the battery went dead, then I can't get it to charge back up. Any suggestions?
  
  
• Re: JVC service or questions
  deb hannan
  - 11th Oct 2006 7:08
  I have a GR-DVP7 Digital video camera & am having problems with the LCD Monitor. When you open the monitor slightly it works, but if you open it all the way it goes off. It has not been dropped or damaged in any way. This problem makes it impossible to use the camera at all. Any solutions or advice?
  
  Thanks
  
  
• Re: JVC service or questions parul bhargava - 11th Oct 2006 17:48
  i dont have the software for transferring the videos to the pc .plz can u sen it to me . model no. GR-D239. THANK U
  
  
• Re: JVC service or questions brad sargent - 12th Oct 2006 17:51
  I have a JVC kd-sh99 car stereo. I have error #6 and more coming up on screen.I always had trouble with the mp3 player to.another thing is the face plate wont stay in it keeps coming not to the first angle sitting
  
  
  • Re[2]: JVC service or questions joe martin - 28th Jul 2007 0:23
    i have a jvc car audio model number kd-sh99 it shows err6,when you close door it reopens shown err6.what could be this cause.
    
    
• Re: JVC service or questions jason davis - 13th Oct 2006 1:00
  Hello Stacy-
  
  I am not sure if you are still responding but I have a problem. My GD-V4210PZW-G works only half the time. The other half, the screen displays a bunch of vertical lines that are separated in half with a horizontal line the runs down the middle of the screen. The lines move with the program being seen and the audio is fine. Any suggestions would be greatly appreciated. Thanks, Jason
  
  
• Re: JVC service or questions Susan Forsgard - 13th Oct 2006 2:20
  I have a JVC Model #AV-27920. I have an all in one remote. My tv turned off by itself tonight and the timer light on the front started blinking. I could not get my remote to operate the tv so I unplugged it for awhile. However, when I plug it back in, the timer light starts bliniing again and the tv goes dead. How do I fix this!
  
  
• Re: JVC service or questions
  Nancy Phelan
  - 13th Oct 2006 5:41
  I have a jvc Television Model #AV27CM4 and I am having trouble with the sound on the TV. I need a manual if one is available. At the moment I hook it up to Direct TV satalite
  Thanks