JVC service or questions

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better.

Stacy Sample
JVC Service & Engineering
Houston, Texas

Reply

• Re: JVC service or questions
  ed
  - 9th Aug 2004 18:34
  I have a JVC GR-DVL520U with an EO1 error similar to post by Joe below:
  ****************
  Re: JVC service or questions @ Joe - 6th Jul 2004 8:37
  Hello,
  I have a JVC GR-D30U and I get a EO1 message...safeguard mode. What do I do to fix it. Thanks
  ****************
  thanks in advance for any help.
  ed.
  
  
  • Re: Re: JVC service or questions Mike - 6th Dec 2004 2:39
    The GR-DVL520U and the GR-D30U have completely different mechanisms but the code is the same, E01 is a loading error, it can be caused by both mechanical and electrical issues. I am a technician that has repaired both models and others made by JVC. The codes that come up are to point the technician in the right general direction. An example of this is your E01 code, E01 is a loading error, it could be bent, jammed, or damaged mechanical parts, sand in the worm gear on the loading motor, a bad loading motor, poor electrical connection on the loading motor, bad driver IC, bad control IC, problem with the mode switch, and the list goes on. So you can see that E01 and other codes are not as simple as it seems on the surface.
    
    
  • Re[2]: JVC service or questions
    dave@NASA
    - 5th Apr 2006 9:48
    hi i solved e01 err [well in this instance anyway- unless there is still a prob with motor drvr's etc.] try split the case into its 2 halves reassemble -- err msg gone -power or gnd link at front of case lower down is split and rejoined by the above procedure - perhaps this causes the s/w reset.
    
    
• Re: JVC service or questions Russ McCaig - 11th Aug 2004 1:33
  I have a JVC 35" TV which had been working fine. Out of the blue the picture went to a single bright line across the center of the TV running horizontally. If you smack the TV on the casing, the picture is seen but then immediately reverts back to the single line. Help!!
  
  
• Re: JVC service or questions
  Mark Dienes
  - 11th Aug 2004 4:08
  I have a GR-D90U and it was working untill I plugged it into a universal power supply. The camcorder uses 11v and once i plugged it into the power supply (dumb idea, it did seem dumb at the moment) it went dead and now will not come on. When I tested the power supply with a volt meter it was putting out 15v no matter what the setting was. Was wanting to know if they have a fuse or something to keep it from frying the board. any help would be great. just dont tell me that I am stuppid I already know that.
  
  
  • Re: Re: JVC service or questions Alex Freiburg - 13th Aug 2004 18:12
    I read down the list further and I did the same exact thing that Mark Dienes did. Can you help us in any way?
    
    
  • Re[2]: JVC service or questions Joe Rara - 15th Oct 2005 8:30
    yeah, mark, that was really stupid of you not to test the output of the powersullpy first. but all hope is not lost. yes, there is a fuse and it can be replaced and no, your board is not fried.
    
    
• Re: JVC service code
  colba
  - 11th Aug 2004 4:15
  Hi i have a JVC tv AV-32D203
  can anyone give me the service code
  please..!!
  
  
  • Re[2]: JVC service code
    JOE
    - 4th Aug 2006 16:35
    did you ever get the service code for a JVC, CRT, TV. I have a 27" that needs B/W tracking Can you help.
    
    
• Re: JVC service or questions
  larry vought
  - 13th Aug 2004 2:26
  I have 27" jvc tv no sound but if i run through my stereo i have sound? but not through the tv .HELP thank you larry
  
  
• Re: JVC service or questions
  Jeremiah
  - 13th Aug 2004 7:17
  I bought a JVC GR D30U digital video camera. In playback the sound cuts in and out. I have cleaned it repeatedly with no help. I would appreciate any help you could give me. Thank You.
  
  
  • Re: Re: JVC service or questions Lou Medeiros - 14th Aug 2004 4:24
    Jeremiah's problems exactly the same as mine (and same model). Purchased in 12/2003. Please help! Problems began in last 2 weeks...
    
    
• Re: JVC service or questions Richard Scarritt - 13th Aug 2004 15:01
  JVC Digicam GR-DVL520U. Started with heads need cleaning message. Then safe mode. Now it won't record at all.
  Help please.
  (Incidentally, JVC's site says Omaha and Lincoln, NE, are the JVC Service Centers closest to Kansas City ...!!
  
  
• Re: JVC service or questions Alex Freiburg - 13th Aug 2004 18:10
  hi, I have a GR-DVL520U and it simply will not turn on. i know of another person with the same problem and he said he sent it in and they replaced the fuse. I have a feeling that is all i need to do. Is there any way I can do this on my own?
  
  
• Re: JVC service or questions Frank - 13th Aug 2004 21:48
  I have the message "EO2 Unit in Safeguard mode - Remove and Reattach Battery" I have done this many times already, but no joy. I you can help me with this I would appreciate it.
  VHS-C Camcorder
  Mod # GR-SXM720U
  Thanks, Frank
  
  
• Re: JVC service or questions Reinard Visser - 14th Aug 2004 0:09
  My gr-d90u does not power up, what might problem be?