JVC service or questions

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better.

Stacy Sample
JVC Service & Engineering
Houston, Texas

Reply

• Re: JVC service or questions Ladi - 12th Apr 2007 9:08
  Hi,
  
  I've had a JVC AV-28WR2EK for 7 years and it has worked fine until recently. Now when the television is switched on it only lasts for about 5 minutes before it switches itself off into Standby mode? Switching it off and then back again causes it do the same thing?
  
  
  • Re[2]: JVC service or questions
    JB38
    - 12th Apr 2007 16:03
    That type of fault would strongly suggest a heat related component breakdown, which for safety reasons causes the power supply to shut back down into its standby mode. It could be absolutely anything that causes that although its most likely to be in the heavier power consuming circuits, and with JVC TV's it could well be centered around the vertical scanning circuit as they are notorious for faults in this area.
    
    
    • Re[3]: JVC service or questions Ladi - 12th Apr 2007 23:15
      Thanks for the reply, I know it's impossible to say so without knowing the exact fault but how much do you think such a repair would cost? Given the age of the television would it better off to buy a new unit?
      
      
• Re: JVC service or questions sissy - 12th Apr 2007 18:34
  I was gave A jvc dual mode digital camera model :GC-A33.I have got a usb cable.please help a old lady get this camera hooked up to her computer so she can get pictures of her grandkids.
  
  
  • Re[2]: JVC service or questions
    JB38
    - 12th Apr 2007 19:33
    Initial advice sent via DIRECT e-mail.
    
    
• Re: JVC service or questions Kevin - 13th Apr 2007 0:49
  I have a JVC model # AV 48WP55.
  
  When plugged in, the power light is lit. However, when I try to turn it on, nothing happens. What can I replace on it to make it work? Even if I have to replace more than what it needs, I don't mind doing that as long as it doesn't get too expensive.
  
  Thanks for your time.
  
  Kevin
  
  
• Re: JVC service or questions
  MARK
  - 14th Apr 2007 3:57
  MY MODEL # IS MX-KB30. HOW DO I REMOVE THE PROTECT MODE ?
  
  
• Re: JVC service or questions
  Ron Scott
  - 14th Apr 2007 17:03
  My GR-D31u doees not show an image on the screen or in the view finder while trying to record. It will play back previously recorded material. The screen remains darkened and the recorder urges me to remove the lens cap while it is already off. Thanks
  
  
• Re: JVC service or questions ASHLEIGH - 14th Apr 2007 17:17
  i have a GR-smx260u that is saying e06 unit im safeguard mode and then it says remove and reattach battery and i do and it says the same thing how do i fix it?
  
  
  • Re[2]: JVC service or questions gator - 23rd May 2007 3:41
    have the same problem and cant find an answer
    
    
• Re: JVC service or questions
  bobby
  - 14th Apr 2007 21:41
  I purchased a jvc 48 I art (model #av-48wp30)tv and when I turn the power on the tv will come on for a few seconds and then go right back off.The problem occured instantainously.If you could help me with my problem it would be greatly appreciated.Thanks Bobby.
  
  
  • Re[2]: JVC service or questions
    JB38
    - 15th Apr 2007 12:09
    Unfortunately not! as its the power unit detecting a power consuming fault and immediately switching back into standby for safety reasons, that being its safeguard mode.
    
    
• Re: JVC service or questions
  jerry soldate
  - 15th Apr 2007 6:15
  1995 jvc av27bm6....its in parental code mode and dont know the code. is their a way to "reboot " tv or ?. thanks for any help
  
  
• Re: JVC service or questions SABS MARTINEZ - 15th Apr 2007 16:57
  my camera is showing safeguard mode and ive tried almost everything my camera model is gr-dvl300us i need help its been doing that forever. if you could please get back to me as soon as possible.
  
  thank you
  
  
• Re: JVC service or questions Jordan Betts - 15th Apr 2007 19:30
  Hello,
  I have the JVC MO # GR-D31U.
  
  One day after it was working just fine for two years, I get a message that says, "Condensation, Operation Paused-- Please Wait"
  
  I did everythign the operational manual says to do, yet the message keeps popping up!
  
  What should I do?
  
  Thank you,
  
  Jordan
  
  
  • Re[2]: JVC service or questions
    JB38
    - 16th Apr 2007 11:43
    Details sent via DIRECT e-mail on first stage remedial action to take regarding this problem.